Description

The Siemens XTRI-S Single Input Monitor Module P/N: S54370-B3-A1 is an intelligent addressable interface module designed for compatible Siemens fire alarm systems. It interfaces a single dry-contact initiating or supervisory device with the system’s addressable device loop.

The XTRI-S can monitor either a normally open (N.O.) or normally closed (N.C.) dry contact and report its status to the fire alarm control panel. It also incorporates dual built-in isolators for enhanced signaling-line circuit survivability.

Product Functions

• Provides one intelligent monitored input
• Monitors N.O. or N.C. dry contacts
• Provides individual addressable point identification
• Uses one device-loop address
• Incorporates dual built-in isolators
• Supports isolator mode
• Supports polarity-insensitive operation
• Provides short-circuit isolation
• Supports Class X circuit configurations
• Provides multi-color LED status indication
• Supports electronic address programming
• Interfaces conventional contact devices with addressable systems
• Designed for compatible Siemens fire alarm systems

Single Input Monitoring

The XTRI-S provides:

One supervised input

This input can monitor:

Normally Open (N.O.)

or

Normally Closed (N.C.)

dry contacts.

The module monitors and reports the condition of the connected contact to the compatible Siemens fire alarm control panel. Unlike the XTRI-R, the XTRI-S does not include an addressable Form C output relay.

Dry Contact Applications

The XTRI-S can interface compatible direct-shorting devices with the Siemens addressable loop.

Typical applications can include:

• Sprinkler valve supervisory switches
• Waterflow switches
• Pressure switches
• Conventional pull stations
• Equipment status contacts
• Other approved dry-contact devices

The actual system response is determined by the programming of the connected fire alarm control panel.

Addressable Operation

The XTRI-S operates as an individually identifiable device on the Siemens device loop.

Addresses Required: One

This allows the fire alarm system to associate the monitored contact with a specific programmed point and location.

Dual Built-In Isolators

The XTRI-S incorporates dual built-in line isolators.

When configured in isolator mode, the isolators operate on both sides of the module and can isolate a line short occurring either before or after the device.

This helps maintain communication with unaffected portions of the addressable loop during certain short-circuit conditions.

Isolator Mode

The XTRI-S supports two primary operating configurations:

Isolator Mode

Polarity-Insensitive Mode

In isolator mode, the dual isolators provide short-circuit protection on both sides of the module.

This architecture can support enhanced signaling-line circuit survivability in compatible Siemens systems.

Polarity-Insensitive Operation

When isolation is not required, the XTRI-S can operate in polarity-insensitive mode.

This provides additional wiring flexibility because the module can communicate properly without requiring polarity-sensitive loop connections in the applicable configuration.

Multi-Color LED

The XTRI-S incorporates a multi-color status LED.

Typical indications include:

Green: Normal supervisory operation

Yellow: Device trouble

Red: Locate or alarm condition

No Flash: No power or device replacement required

The LED provides local visual indication of module and monitored circuit status.

Electronic Address Programming

The XTRI-S supports electronic device programming using the Siemens:

DPU — Device Programmer / Test Unit

DPU Part Number: 500-033260

This allows the module address to be programmed and verified without mechanical DIP or rotary address switches.

System Compatibility

The XTRI-S is designed for compatible Siemens fire alarm platforms including:

Desigo Fire Safety

Cerberus PRO

and supported modular/voice configurations.

Current Siemens documentation also lists the XTRI family for applicable FireFinder XLS, Desigo Fire Safety Modular, Cerberus PRO Modular, and voice modular systems.

Electrical & Interface Information

Model: XTRI-S

Part Number: S54370-B3-A1

Device Type: Single Input Monitor Module

Inputs: One

Contact Type: N.O. / N.C. Dry Contact

Operating Voltage: 13–32 VDC

Maximum Active/Standby Current: 500 µA

Maximum Average Current Draw: 650 µA

Addresses Required: One

Built-In Isolators: Two

Wire Size: 18–14 AWG

Operating Temperature: 32°F to 120°F / 0°C to 49°C

Relative Humidity: 0–95%, non-condensing

Status Indicator: Multi-color LED

Siemens currently identifies XTRI-S / S54370-B3-A1 as an active product.

XTRI-S Datasheet